How To Detail A Boat

How To Detail A Boat

Boat Detailing Secrets You Need To Know

Few things in life compare to the peace and solitude that you can experience while relaxing in a boat out on the open water. Unfortunately, over time, even the best-maintained boats can become dirty. The combination of being surrounded by moist, humid air and being partially submerged in the water can cause dirt, algae, and other contaminants to build upon the surface. These contaminants can even begin to affect the boat’s interior. Boat Detailing is a great way to remove all of the dirt and grime &restore it back to its original condition. The step-by-step guide below provides detailed information on how to clean, restore, and protect your boat. As you read through these boat detailing tips, you will discover helpful information on the products and cleaning methods that you should use if you want to get the best results.

Step 1 – Begin by rinsing off your boat

Before you really get into the nitty-gritty of boat detailing, you should give it a good rinse with clean, fresh water. This will help loosen any dirt or debris on the surface. Begin rinsing at the top of the boat, working toward the bottom. Keep in mind, this initial rinse is designed to take care of the surface dirt. You still will need to thoroughly clean it by hand to eliminate all of the stuck-on dirt and grime. Choose a nozzle for your hose that provides a strong, steady stream of water. Alternatively, if you have access to a pressure washer, you can get even better results.

Step 2 – Scrub down your boat

The next step is to begin scrubbing the boat, removing any accumulated dirt or grime that was too stuck-on to be washed away when you hosed the boat down. Invest in a high-quality cleaner that is specifically designed for boats. Using this cleaner and appropriate sponges or cleaning cloths, begin lathering up the outside of the boat, scrubbing away any dirt. Work in small sections, rinsing away the soap as you go. Avoid allowing the soap to dry on the boat since it can be difficult to remove and can result in streaking. The cleaner you can get your boat, the better any protective treatments you apply will work. Look for a cleaner that can be used on all of the different surfaces that are found inside your boat.

Step 3 – Buff and shine the surface

After you finish scrubbing your boat, it will be much cleaner. However, it may look a little bit dull and lackluster but do not worry just yet. To restore its shine, use a buffing cloth or a rotary buffer. This will help bring the surface of the boat back to life, giving it a beautiful shine that makes it look like new. Do not skip this step in the process of your boat detailing journey.

Step 4 – Wax the surface of your boat

Once your boat has been thoroughly cleaned, you should apply a layer of wax. This will not only help it shine like new but it will also protect it against any future dirt that you encounter. Waxing improves the look of your boat while at the same time providing it with essential protection. By taking the time to wax it now, you can make detailing it much easier in the future. Again, work in small areas rather than trying to do the whole thing at once. Apply the wax to each section of the boat, using a soft cloth to work it in and then buffing it out until it has a beautiful shine. By the time you are done, your boat should look like new. To get the best results, make sure that the wax you purchase is specifically designed for boats. Boat wax is formulated to resist water far better than the wax that is designed for cars. To maintain the shiny look of the fresh wax, periodically use a spray-on speed-detailer.

Step 5 – Clean the interior of the boat

Interior boat detailing is only the first part of the process. You still need to address the interior. Invest in a cleaner that will work on multiple surfaces. The cleaner that you choose should do a good job of cutting through dirt and grime but should be mild enough that it doesn’t harm any of the interior surfaces. If you encounter any particularly challenging stains, consider using a 303 spot cleaner to remove them. Any metal fixtures in your boat interior can be cleaned and reconditioned using metal polish. To keep metal surfaces shiny, consider applying a coat of wax to them, as well.

Step 6 – Finalize the process

After putting so much hard work into cleaning and waxing your boat, you no doubt want to keep it looking its best for as long as possible. Maintaining the like-new look of a freshly detailed boat is easy when you use the right products. Apply protectants to any surfaces that will be exposed to the sun. For instance, vinyl, rubber, and plastic surfaces should be coated with an aerospace protectant. Gel coat surfaces, on the other hand, can be freshened up with a speed detailer. You should also use a special protectant on fabric surfaces to protect them from moisture, mold, and mildew. Following these steps should help you keep your boat looking its best far into the future.

For more related content be sure to check out our boat detailing blog, we are constantly putting out helpful articles on detailing. Boat Detailing is important if you are wanting to make your boat last. You can contact a professionals boat detailing expert today by giving us a call at (855) 335-2719.

No Comments

Post A Comment

Call Now Button(855) 335-2719